/
/
/
/
/
Dynacord DSA 8204

Dynacord DSA 8204

Dynacord DSA 8204

Audio pojačavač snage 2 x 450W na 4ohm

Namenjen fiksnim instalacijama, mogućnost kontrole računarom (IRIS Net softver)

- Najbolje audio performanse za sve ProSound aplikacije
- Optimizovano za rad 24/7
- Maksimalna pouzdanost zahvaljujući DINACORD zaštitnoj šemi

850.00

DYNACORD Digital System series amplifiers offer a package of reliable high output power, high efficiency and legendary pro audio performance. They are the premium choice as system drive for a variety of DYNACORD‘s installation loudspeakers like e.g. D-Lite, Forum, VariLine or Cobra loudspeaker families. Their comprehensive protection system includes circuitry against overheating, overload, short circuit, HF and DC as well as back-EMF. A soft start circuit compensates mains inrush current peaks and thus prevents triggering AC mains fuse when switching on the amplifier.
Loudspeakers are protected by turn-on-delay relays. Using an optional RCM-810 Remote Control Module allows supervision of the amplifier and connected loudspeakers via IRIS-Net software.

-Load impedance 2 Ω 4 Ω 8 Ω
-Maximum midband output power, THD = 1%, 1 kHz, Dual channel 650 W 450 W 270 W
-Rated output power, THD < 0.1%, 20–20 000 Hz – 400 W 200 W
-Maximum single channel output power, dynamic-headroom, IHF-A 1150 W 660 W 350 W
-Maximum single channel output power, continuous, 1 kHz 850 W 540 W 310 W
-Maximum bridged output power, THD = 1%, 1 kHz – 1300 W 900 W
-Maximum RMS voltage swing, THD = 1%, 1 kHz 55.3 V
-Power Bandwidth, THD = 1%, ref. 1 kHz, half power at 4 Ω 10–30000 Hz
-Voltage gain, ref. 1 kHz 32 dB
-Input Sensitivity, rated power at 8 Ω, 1 kHz +2.2 dBu (1.0 Vrms)
-THD at rated output power, MBW = 80 kHz, 1 kHz < 0.03%
-IMD-SMPTE, 60 Hz, 7 kHz < 0.1%
-DIM30, 3.15 kHz, 15 kHz < 0.05%
-Maximum input level +21 dBu (8.69 Vrms)
-Crosstalk, ref. 1 kHz, at rated output power < –80 dB
-Frequency response, ref. 1 kHz 10–40000 Hz (±1 dB)
-Input impedance, active balanced 20 kΩ
-Damping factor, 1 kHz > 300
-Slew rate 25 V/μs
-Signal-to-noise ratio (A-weighted) > 106 dB
-Output noise, A-weighted < –71 dBu
-Output stage topology Class AB
-Power requirements 240, 230, 120 or 100 V; 50–60 Hz (factory configured)
-Power consumption, 1/8 maximum output power at 4 Ω 470 W
-Power consumption, rated output power at 8 Ω 670 W
-Mains fuse
• 240/230 V T10AH
• 120/100 V T20AH
-Protection Audio Limiters, High Temperature, DC, HF, Back-EMF, Peak Current
-Limiters, Inrush Current Limiters, Turn-on Delay
-Signal Processing HPF, 18 dB, switchable
-Cooling Front-to-Rear, 3-Stage-Fans
-Operating temperature 5° to 40° C (40° to 105° F)
-Safety class I
-Product dimensions (Width x Height x Depth) 483 x 88.1 x 421.5 mm
-Net weight 12.6 kg

Specifikacija
SERIJA: Dyacord DSA
BROJ KANALA: 2
KLASA POJACAVACA: AB
ULAZNI SIGNAL KONEKTORI: Feniks
IZLAZNI SIGNAL KONEKTORI: Feniks
Snaga po kanalu na 2 Ω (Single Channel): 850 W
Snaga po kanalu na 4 Ω (Single Channel): 540 W
Snaga po kanalu na 8 Ω (Single Channel): 310 W
Snaga po kanalu 2 Ω (Dual Channel): 650 W
Snaga po kanalu 4 Ω (Dual Channel): 450 W
Snaga po kanalu 8 Ω (Dual Channel): 270 W
Snaga po kanalu 4 Ω (Bridge): 1300 W
Snaga po kanalu 8 Ω (Bridge): 900 W
ZASTITNE FUNKCIJE: Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters, Turn-on delay
RACK UNITS: 2 U
NAPAJANJE: 240 V, 230 V, 120 V or 100 V; 50 Hz to 60 Hz (factory configured)
VISINA (H): 88.1 mm
SIRINA (W): 483 mm
DUBINA (D): 421.5 mm
NETO TEZINA: 12.6 Kg
Opis proizvoda

DYNACORD Digital System series amplifiers offer a package of reliable high output power, high efficiency and legendary pro audio performance. They are the premium choice as system drive for a variety of DYNACORD‘s installation loudspeakers like e.g. D-Lite, Forum, VariLine or Cobra loudspeaker families. Their comprehensive protection system includes circuitry against overheating, overload, short circuit, HF and DC as well as back-EMF. A soft start circuit compensates mains inrush current peaks and thus prevents triggering AC mains fuse when switching on the amplifier.
Loudspeakers are protected by turn-on-delay relays. Using an optional RCM-810 Remote Control Module allows supervision of the amplifier and connected loudspeakers via IRIS-Net software.

-Load impedance 2 Ω 4 Ω 8 Ω
-Maximum midband output power, THD = 1%, 1 kHz, Dual channel 650 W 450 W 270 W
-Rated output power, THD < 0.1%, 20–20 000 Hz – 400 W 200 W
-Maximum single channel output power, dynamic-headroom, IHF-A 1150 W 660 W 350 W
-Maximum single channel output power, continuous, 1 kHz 850 W 540 W 310 W
-Maximum bridged output power, THD = 1%, 1 kHz – 1300 W 900 W
-Maximum RMS voltage swing, THD = 1%, 1 kHz 55.3 V
-Power Bandwidth, THD = 1%, ref. 1 kHz, half power at 4 Ω 10–30000 Hz
-Voltage gain, ref. 1 kHz 32 dB
-Input Sensitivity, rated power at 8 Ω, 1 kHz +2.2 dBu (1.0 Vrms)
-THD at rated output power, MBW = 80 kHz, 1 kHz < 0.03%
-IMD-SMPTE, 60 Hz, 7 kHz < 0.1%
-DIM30, 3.15 kHz, 15 kHz < 0.05%
-Maximum input level +21 dBu (8.69 Vrms)
-Crosstalk, ref. 1 kHz, at rated output power < –80 dB
-Frequency response, ref. 1 kHz 10–40000 Hz (±1 dB)
-Input impedance, active balanced 20 kΩ
-Damping factor, 1 kHz > 300
-Slew rate 25 V/μs
-Signal-to-noise ratio (A-weighted) > 106 dB
-Output noise, A-weighted < –71 dBu
-Output stage topology Class AB
-Power requirements 240, 230, 120 or 100 V; 50–60 Hz (factory configured)
-Power consumption, 1/8 maximum output power at 4 Ω 470 W
-Power consumption, rated output power at 8 Ω 670 W
-Mains fuse
• 240/230 V T10AH
• 120/100 V T20AH
-Protection Audio Limiters, High Temperature, DC, HF, Back-EMF, Peak Current
-Limiters, Inrush Current Limiters, Turn-on Delay
-Signal Processing HPF, 18 dB, switchable
-Cooling Front-to-Rear, 3-Stage-Fans
-Operating temperature 5° to 40° C (40° to 105° F)
-Safety class I
-Product dimensions (Width x Height x Depth) 483 x 88.1 x 421.5 mm
-Net weight 12.6 kg